Automation Fair®, Booth #1317: MVP Tips for Your Applications, Prizes, and More! Learn More
Printer friendly version of this page. Find a Distributor near you.
PLX31_MBTCP_MBS4

EtherNet/IP™ 转 ASCII 四端口通信网关

PLX31-EIP-ASCII4

ProSoft Technology 的 EtherNet/IP™ 转 ASCII 四端口通信网关可实现在 EtherNet/IP™ 的 PAC 和 ASCII 设备 (磅秤和条码扫描器) 之间进行高速双向数据传输。EtherNet/IP™ 协议驱动程序支持显式报文模块。网关可由用户配置,作为客户端或服务器使用。

EtherNet/IP™ PAC 包括罗克韦尔自动化 ControlLogix® 和 CompactLogix™ 以及多种施耐德电气控制器。该模块在许多行业中有广泛应用,特别是制造业、石油与天然气、电力和食品加工等行业。

网关功能众多,集成简便,可大大缩短调试时间,优化性能。

图像

Click on image(s) to enlarge
Drag with the mouse. Click for close.

特性 优势

  • 数据优先级管理:支持多 I/O 连接,可为状态和/或控制数据设置不同 RPI,以优化以太网带宽。
  • 内置嵌入式 EDS 附加组态文件,集成简便,可大大缩短调试时间。
  • 内置 SD 卡卡槽 (SD 卡为选配件),方便存储组态文件。这可用于故障恢复。
  • ProSoft Discovery Service:这是一个实用程序,通过它,无需处于相同子网便可在 PC 上查看网关,更改缺省 IP 地址。

规格

规格

EtherNet/IP™ 规格

规格

描述

3 类服务器连接数目

5

支持的 PLC 类型

PLC2、PLC5、SLC、CLX、CMPLX

支持的消息类型

PCCC 和 CIP

3 类客户端连接

已连接 - 2

未连接 - 1

1 类 I/O 连接数目

2

I/O 连接大小

248/248

最大 RPI 时间

每个连接 5 ms

支持的 CIP 服务

0x4C - CIP 数据表读取

0x4D - CIP 数据表写入

命令列表

每台客户端支持 100 条命令,每条均可针对命令类型、IP 地址、寄存器寻址和字/位计数进行配置。

命令集

PLC-2/PLC-3/PLC5 基本命令集

PLC5 二进制命令集

PLC5 ASCII 命令集

SLC500 命令集

ASCII 规格

发送和接收
 缓冲区大小

发送字符长度 255 字节,每个发送字符之间的延迟时间为 0 到 65535 毫秒

 

硬件规格

规格

描述

电源

标称值 24 VDC
 允许 10 至 36 VDC
 正、负、GND 端子

电流负载

标称值 24 VDC @ 300 mA

10 到 36 VDC @ 最大值 610 mA

工作温度

-25°C 至 70°C (-13°F 至 158°F)

存储温度

-40°C 至 80°C (-40°F 至 176°F)

抗冲击性

IEC 60068-2-27;15G @ 11ms,3 轴 (工作时)

IEC 60068-2-27;30G @ 18ms,3 轴 (不工作时)

抗振性

IEC 60068-2-6;5G @ 10 至 150 Hz

相对湿度               

5% 至 95% RH,无冷凝

尺寸 (H x W x D)

5.38 x 1.99 x 4.38 in
 13.67 x 5.05 x 11.13 cm

LED 指示灯

 

组态 (CFG)、错误 (ERR)、电源 (PWR)、硬件故障 (FLT)、网络状态 (NS)、EtherNet/IP™ I 类或 III 类连接状态 (仅 EtherNet/IP) 模块状态 (MS)、模块组态状态 (仅 EtherNet/IP) 以太网通信端口链接/活动和 100 mbit 串行通信端口接收 (RX) 和发送 (TX)

以太网端口

 

10/100Mbit 半双工 RJ45 连接器,50 Hz 到 60 Hz 时电气隔离 1500 Vrms 达 60 秒,遵循 IEC 60950:1991 的第 5.3.2 节中的规定。以太网广播风暴弹性不超过 5000 [ARP] 帧/秒,持续时间不超过 5 分钟

串行端口数量

4

串行端口隔离

2500 Vrms 端口信号隔离,符合 UL 1577 规定,串行端口通信信号使用 RF (射频) 调制信号作为隔离介质,IC 芯片型号为 SiliconLabs Si844x (Si8440、Si8441、Si8442)

每台设备均配备

2.5 mm 螺丝起子

ProSoft 解决方案 DVD

J180 电源连接器

(4) RJ45-DB9M 串行适配器电缆 (串行协议)

(4) DB9 转接螺栓型端子适配器 (串行协议)

5 英尺直通以太网电缆

 

机构认证和证书

CE Mark

 

UL/cUL Class I Div II

 

ATEX 2 区

 

CB Safety

 

协议

PLX30-EIP Protocol Secifications


Protocol Specifications

EtherNet/IP® Specifications

 Number of Class 3 Server Connections

5

Supported PLC Types

PLC2, PLC5, SLC, CLX, CMPLX

Supported Message Types

PCCC and CIP

Number of Class 3 Client Connections

 

Connected
Unconnected

2
1

Number of Class 1 I/O Connections

 

PLX31-EIP-MBTCP/MBS
PLX31-EIP-MBS4
PLX31-EIP-ASCII
PLX31-EIP-ASCII4
PLX31-EIP-SIE

2
8
1
4
2

I/O connection sizes

248/248

Max RPI time

5ms per connection

CIP Services Supported

0x4C - CIP Data Table Read
0x4D - CIP Data Table Write

Command List

Support for 100 commands per Client, each configurable for command type, IP address, register to/from addressing and word/bit count.

Command Sets

PLC-2/PLC-3/PLC5 Basic Command Set
PLC5 Binary Command Set
PLC5 ASCII Command Set
SLC500 Command Set

 

Modbus TCP/IP Specifications

Supported Modbus Function Codes

1: Read Coil Status
2: Read Input Status
3: Read Holding Registers
4: Read Input Registers
5: Force (Write) Single Coil
6: Preset (Write) Single Holding Register

15: Force (Write) Multiple Coils
16: Preset (Write) Multiple Holding Registers
22: Mask Write Holding Register (Slave Only)
23: Read/Write Holding Registers (Slave Only)

Supported Clients

10

Supported Servers

 

MBAP
Encapsulated

5
5

 

Command List

Up to 160 fully configurable Client commands

Status Data

Error codes reported individually for each command

Command List Polling

Each command can be individually enabled or disabled; write-only-on-data-change is available

 

Modbus Serial Specifications

Command List

Up to 100 commands per Master port, each fully configurable for Function Code, slave address, register to/from addressing and word/bit count.

Supported Modbus Function Codes

1: Read Coil Status
2: Read Input Status
3: Read Holding Registers
4: Read Input Registers
5: Force (Write) Single Coil
6: Preset (Write) Single Holding Register

15: Force (Write) Multiple Coils
16: Preset (Write) Multiple Holding Registers
22: Mask Write Holding Register (Slave Only)
23: Read/Write Holding Registers (Slave Only)

Software configurable communication parameters

Baud rate: 110 baud to 115.2 kbps Parity: None, Even, Odd Data Size: 7 or 8 bits Stop bits: 1 or 2 RTS on/off delay: 0 to 65535 milliseconds
Modbus Modes RTU mode (binary) with CRC-16ASCII mode with LRC error checking, Floating point data movement supported including configurable support for Enron and Daniel implementations

Polling of Command List

Configurable polling of command list, including continuous and on change of data, and dynamically user or automatic enabled.

Status Data

Error codes available on an individual command basis. In addition, a slave status list is maintained per active Modbus Master port.

Node Address

1 to 247 (software selectable)

RS Interface

RS232, RS422, and RS485

 

ASCII Specifications

Ports Available in up to four port configurations to receive and/or transmit data

Transmit and Receive Buffer Size

255 byte Transmit character length with 0 to 65535 millisecond delay between each transmitted character

 

Siemens Industrial Ethernet Specifications

Specification

Description

Supported PLC Data Exchange (Read and Write)

Siemens S7-200, Siemens S7-300, Siemens S7-400,
Siemens S7-1200

Supported Register Types

DB, Inputs, Outputs, Flags, Counters, Timers

Supported Clients

20


ASCII Protocol Specification


The ASCII protocol driver permits the module to interface to many ASCII devices. Each ASCII port on the module is configurable to send and/or receive ASCII strings, each supporting its own individual serial network.


Protocol Specifications

The ASCII driver provides a powerful connection between the internal application database in the ProLinx unit and devices supporting serial ASCII communications (bar code scanners, line printers, legacy terminal based computer systems, etc).

The serial port on the gateway is user-configurable to support ASCII communications (Baud rate, Data Bits, Stop Bits, etc). The ASCII port can act as a Master (Send ASCII strings) or as a Slave (Receive ASCII strings), or both.

ASCII Specifications

Ports

Available in up to four port configurations to receive and/or transmit data.

Transmit and Receive buffer size

255 bytes each

Transmit character with pacing

0 to 65535 millisecond delay between each transmitted character.


证书

Ex Certificate (ATEX Directive) 84.06 kB 最后修改 2015.05.22
CB Safety 327.80 kB 最后修改 2015.05.22
Korean KC Registration 548.37 kB 最后修改 2015.05.22
UL/cUL; Class 1, Div 2 67.02 kB 最后修改 2013.03.19
Declaration of Conformity (RoHS/CE) 297.32 kB 最后修改 2018.07.25
EtherNet/IP - Declaration of Conformity 183.48 kB 最后修改 2018.08.01