Configuration Utility Integrates Tightly with Unity Pro

• Application-specific Variable and Function Block files are automatically generated.
• Users are not required to develop communication logic or tag structures in their PLC or PAC projects.

Configuration Archive and Diagnostics

• The gateway configuration file can be stored in an industrial SD card. This allows for rapid disaster recovery by moving the SD card from a failed gateway to a replacement gateway.
• Extensive diagnostics for the gateway and for both Modbus TCP/IP and IEC 61850 networks are available via the configuration utility.

Import Configured IED files

• All IED data attributes are available for convenient mapping to Modbus registers.

Modbus TCP/IP Client/Server support

• Enables multiple Modbus TCP/IP devices or SCADA devices to interface with IEC 61850 devices simultaneously.

Hardware

Two (2) Ethernet ports for Modbus TCP/IP and IEC 61850 communication

Software

ProSoft 61850 Configuration Manager for configuration and diagnostic viewing

ProSoft 61850 Tag Monitor for viewing live tag data

ProSoft Discovery Service for setting a temporary IP address

Configuration Storage

Internally stored, by default. Configuration settings can be saved on an optional removable 1GB Industrial SD Card

ProSoft 61850 Configuration Manager saves configuration information to an offline file.

Modbus Commands Supported

(Client and server)

3: Read Holding Registers

16: Preset (Write) Multiple Holding Registers

Configurable Parameters (Client and server)

Gateway IP Address

PLC Read Start Register (%MW)

PLC Write Start Register (%MW)

Number of MBAP and MNET servers

Gateway Modbus Read Start Address

Gateway Modbus Write Start Address

Configurable Parameters (Client Only)

Minimum Command Delay

Response Timeout

Retry Count

Command Error Pointer

Command List

Maximum 2000 Modbus Client commands (one IEC

Data Attribute per command)

Status Data

Error codes reported individually for each command

High-level status data available from Modbus TCP/IP Client through MNET server (for example PLC or PAC)

Command List Polling

Each command can be individually enabled or disabled; write-only-on-data-change is available

ACSI Basic Conformance

SCSMs supported

SCSM: IEC 61850 8.1(MMS) used

ACSI Model Conformance

Reporting

Buffered Report Control Block (BRCB)

Unbuffered Report Control Block (URCB)

GOOSE

entryID, DataReflnc

Control

Direct-with-Normal-Security

SBO-with-Normal-Security

Direct-with-Enhanced-Security

SBO-with-Enhanced-Security

Logical Nodes

IEC 61850 Logical Nodes, including Logical

Nodes for Hydro Power Plants and Logical Nodes for Wind Power Plants

Configurable Parameters

MMS Command Delay

Status Data

Status available per node

Report and GOOSE status available

High-level status data available from Modbus TCP/IP Client through the MNET server (for example PLC or PAC)

Configurable Parameters

SNTP/NTP server synchronization rate (in minutes)

SNTP/NTP server Address

Specification

Description

Power Supply

24 VDC nominal
10 to 36 VDC power input allowed
Positive, Negative, GND Terminals
2.5 mm screwdriver blade

Current Load

200 mA max @ 24 VDC
150 mA max @ 32 VDC
450 mA max @ 10 VDC

Operating Temperature

0°C to 70°C (32°F to 158°F)

Storage Temperature

-40°C to 85°C (-40°F to 185°F)

Relative Humidity

5% to 95%, with no condensation

Dimensions H x W x D

14.02 x 5.23 x 11.1 cm
5.52 x 2.06 x 4.37 in

Shock

IEC 60068-2-27; 15G @ 11ms (Operational)
IEC 60068-2-27; 30G @ 18ms (Non-Operational)

Vibration

IEC 60068-2-6; 5G, 10 to 150 Hz

LED Indicators

ERR, CFG, FLT, PWR

Ethernet Ports (E1, E2)

10/100 Base-T full- and half-duplex RJ45 Connector Link and Activity LED indicators

Electrical Isolation 1500 V rms at 50 to 60 Hz for 60 s, applied as specified in section 5.3.2 of IEC 60950: 1991

Ethernet Broadcast Storm Resiliency = less than or equal to 5000 [ARP] frames-per-second and less than or equal to 5 minutes duration

Shipped with Each Unit

One - J180 screw terminal plug
One - HRD250 screwdriver